|
Hi-Q DC Antenna Controller
Hi-Q DC-H,HF antenna controller.
It was developed for the USMC On the Move H-Q HF antennas.
The same circuit board and components used for the "H" (Ham)
version, except the Mil. connectors we use the simple 3 and 4 pin connectors.
|
|
Hi-Q Capacitance Hat with Extension
CapHat, a capacitance hat for ANY mobile antenna, installs above the loading coil with either a 3/8-24 stainless steel stud or an extension rod.
CapHat comes with a stainless steel 3/8-24 stud and 3/8-24 threaded hole for the whip. It has four "lobes" -- No dangerous rods sticking out! Constructed of nickel plated hub, four 3/32 dia. 304 SS lobes.
|
|
Hi-Q 3/80 RT
The Hi-Q-3/80 RT
Remotely Tunable (Motorized) - 6 thru 80 meters
The Hi-Q-3/80 RT is a motorized, Remotely Tunable HF Mobile antenna
|
|
Hi-Q 3/80 RT
The Hi-Q-3/80 RT
Remotely Tunable (Motorized) - 6 thru 80 meters
The Hi-Q-3/80 RT is a motorized, Remotely Tunable HF Mobile antenna
|
|
Hi-Q 3/80 RT
The Hi-Q-3/80 RT
Remotely Tunable (Motorized) - 6 thru 80 meters
The Hi-Q-3/80 RT is a motorized, Remotely Tunable HF Mobile antenna
|
|
Hi-Q 3/80 RT
The Hi-Q-3/80 RT
Remotely Tunable (Motorized) - 6 thru 80 meters
The Hi-Q-3/80 RT is a motorized, Remotely Tunable HF Mobile antenna
|
|
Hi-Q 3/80 RT
The Hi-Q-3/80 RT
Remotely Tunable (Motorized) - 6 thru 80 meters
The Hi-Q-3/80 RT is a motorized, Remotely Tunable HF Mobile antenna
Dimensions:
Antenna height: 3 feet
Recommended whip length: 7 feet 6 inches
Loading coil diameter: 3 inches
Loading coil length: 9 inches
Mast diameter: 1.3 inches with 2 inch motor housing
Weight: 4.5 lb.
Base impedance: 18 Ohms @ 3.8 MHz
|
|
Hi-Q 3/80 RT
The Hi-Q-3/80 RT
Remotely Tunable (Motorized) - 6 thru 80 meters
The Hi-Q-3/80 RT is a motorized, Remotely Tunable HF Mobile antenna
Dimensions:
Antenna height: 3 feet
Recommended whip length: 7 feet 6 inches
Loading coil diameter: 3 inches
Loading coil length: 9 inches
Mast diameter: 1.3 inches with 2 inch motor housing
Weight: 4.5 lb.
Base impedance: 18 Ohms @ 3.8 MHz
|
|
Hi-Q GQD
GQD - Giant Quick Disconnect
The GQD is a 2" diameter 6061-T6 CNC machined nickel plated aluminum (Stainless available at extra charge) BAYONET type quick disconnect. Used at the base of the mobile antenna for QUICK removal and stowage, it gets your expensive investment out of site. Also perfect for moving the mobile antenna from car to car, or from car to base. It has on the lower base a 3/8-24 threaded hole and the top part has a 3/8-24 stainless steel stud for the antenna. Uses a heavy-duty spring, with approximately 60 lb of force needed to remove. The GQD should work for any HF Mobile antenna base using a 3/8-24 connector
|